Pro112 ECU
$1,798.06 USD
Skip to product information
Pro112 ECU
$1,798.06 USD
Shipping calculated at checkout.
Payment methods
Pickup available at Fast UTV
Usually ready in 5+ days
| Processor | The Pro112 uses the industry leading superfast MPC5554 80mhz Processor |
| Injectors | 8 Saturated Injector Drivers (peak and hold injectors must use a resistor pack on this ECU) |
| Coils | 8 |
| TPS | Yes – Adaptive |
| Coolant Temp | Yes |
| Air Temp | Yes |
| Map Sensor | Yes – Unlimited Range |
| MAF Sensor | Yes – Frequency and Voltage |
| Idle Control | Pulse Width and Stepper motor – Adaptive |
| Wideband O2 | Uses CAN Based UEGO Control (External capable) |
| Cam | Yes – Hall/Digital Only VR Cam Sensors must use converter box Part #9033 |
| Crank | Yes – Hall/VR capable |
| Variable Cam | Yes 4 cam capable |
| Knock Channels | 2 Programmable frequency and event with individual cylinder notification |
| Flex Fuel Capability | Add a Flex fuel sensor, and the computer automatically adjusts fuel, timing, and boost based on Ethanol content! Multiple Failsafes! |
| Nitrous Control | 4 stages multiple event trigger control range. V.E. based fueling**** |
| Boost Control | Most comprehensive and easy to use Antilag on the market bar none! Change your target with no re-tuning, set targets below spring pressure…no problem! Multiple control strategies.*** |
| Rolling AntiLag Control | Speed based capture (no preset rpm or speed…press it and go) |
| Rev Limiters | Multiple – Burnout, Stage, TwoStep, Rolling Antilag (True RPM capture at ANY Speed) All tied to separate boost targets! |
| Traction Control | Multiple control strategies, most advanced traction control system on the market.*** |
| Launch Control | Comprehensive Launch Control Strategies to get the most powerful cars down the nastiest tracks! |
| Valet Modes | Two Stages – Tied to Fault management – Power Reduction, Speed limited etc.. No laptop connection required to active or deactivate, calibratable procedure |
| Drive Off Assist | Drive Off limiters to help with light rotating mass and grabby clutches |
| Fuel Pump Control | Yes, multiple staged pumps and pulse driven pumps* |
| Analog Inputs | 34* Fuel Pressure monitoring and feedback correction, Oil Pressure, Exhaust Backpressure Feedback and correction, and much more. |
| Low Side Outputs | 14 total – 4-7amp capable – 6-700ma capable, 2 1amp capable, 2 350ma capable, 1 100ma capable. 4 of these are PW capable (LS2, LS8, LS9, LS10)* |
| Tach | Yes – Software configurable |
| Digital Inputs | 3 channels (Not including Cam/Crank inputs)- Fully programmable pre configured |
| High Current Bridges | 2 channel sets – Used for Stepper motor control, or Electronic Throttle Control |
| Drive By Wire | Yes – Dual capable* |
| Fault Coding Safety | Yes** |
| MIL (CEL) | Yes – Malfunction indicator with fault codes |
| Main Relay Control | Yes |
| 5v Ref | 2 locations |
| Sensor Grounds | 2 locations |
| Key Switch Power | Yes |
| Permanent Power | Yes |
| Battery Backup | No – Not needed – Stored permanently! |
| Chassis Ground | 3 Locations |
| Can Channels | 3 Channels |
| RS485 Connection | Yes***** |
| Internal Memory | Limited to Fault logic |
| USB Direct Connection | No |
| Laptop Connection | USB |
Logging with PC attached included on all ECU’s. If logging without the PC connected is required, you must purchase one of the external loggers. This module simply connects through the CAN bus and is configurable, however it is preconfigured by Pro EFI for common channels to be logged
- The amount of available channels is dependent upon the use of pre configured I/O such as Fuel pump, TPS, etc…
- Fault coding is a strategy used by the O.E. manufacturers. This strategy allows for the capability to trigger faults and fault actions. Features include but are not limited to multiple safety strategies for limiting boost and shutting off nitrous control under lean conditions. See your Authorized Professional EFI Dealer for more information.
- Multiple Strategies are configurable based upon time or speed. See your Authorized Professional EFI Systems Dealer for more information.
- V.E. stands for volumetric efficiency. This is a strategy incorporated by the O.E. manufacturers to more accurately determine the fueling requirements of the engine. There are several advantages to using this method. See your Authorized Professional EFI Systems Dealer for more information.
- These communication ports are dedicated for the use of future external peripherals to be announced by Professional EFI Systems at a later date.
Fast UTV is a certified systems installer for ProEFI and all of the ProEFI systems need to be installed and TUNED on a DYNO. We offer all of this here; LIKE NO OTHER PLACE.
Purchase online and give us a call for installation! (951) 427-7466
Adaptive – Is a term meaning that particular feature will self tune itself constantly. This is another strategy used by the O.E. manufacturers to help keep the vehicle in a constant state of tune for hundreds of thousands of miles.
Frequently asked questions
What is the return policy?
Our goal is for every customer to be totally satisfied with their purchase. If this isn't the case, let us know and we'll do our best to work with you to make it right.
Are any purchases final sale?
We are unable to accept returns on certain items. These will be carefully marked before purchase.
When will I get my order?
We will work quickly to ship your order as soon as possible. Once your order has shipped, you will receive an email with further information. Delivery times vary depending on your location.
Where are your products manufactured?
Our products are manufactured both locally and globally. We carefully select our manufacturing partners to ensure our products are high quality and a fair value.
How much does shipping cost?
Shipping is calculated based on your location and the items in your order. You will always know the shipping price before you purchase.
